Thermal insulation llight weight gypsum perlite plaster
Plaster Gypsum Perlite is composed of a retarded gypsum, Perlite and selected aggregates with special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce cohesive mix. Plaster Gypsum Perlite is a high quality product and provides as underlayment on various facets of the projects.
Plaster Gypsum Perlite stored in 25 Kg Bag or Bulk. Consumption - 1 Kg / m2 / mm
Original sealed container of Plaster Gypsum Perlite has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
For manual mixing, add to the mixing container 10.5-11.5 litres of water for each 25 Kg bag of Plaster Gypsum Perlite or 11-12 litres/25 kg bag for machine application. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Leave the mixed material to stand for 5 min and briefly remix without addition of water.
Manual mixing is allowed for small batch quantities and mix for approx. 1-2 min or when homogenous mix is achieved.
When required add 0.5 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as above.
Mixed material must be used within 30 minute. Do not add water once the mixed plaster mortar start to stiffen or harden.
Plaster Gypsum Perlite is generally applied in a single coat method. Use directly on block walls & rough surfaces. On smooth concrete surfaces apply first a primer coat of Vetobond PB433.
Apply mixed material using spray machine or trowel technique to cover the area to desired thickness. Lightweight leveling tools are required in conjunction with trowel to fill in holes.
When the plaster stiffens lightly, treat the surface to a smooth level to eliminate all traces of protrusions and undulations.
Let the plaster set for about 30 min., using wet sponge, wipe the surface to a creamy smooth finish.
Apply Vetocoat Finish WR white mixed with the right amount of mixing water and 0.5 Ltr of Vetobond PB433 at 2 mm thickness prior to application of decorative paints.
Let the Plaster Gypsum Perlite to fully dry itself. Do not use water.
Paints & Coatings can be applied once the plaster and Vetonit Finish WR has dried out completely, generally after 7 days.
The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Prior to Plaster Gypsum Perlite application, wet the entire surfaces with clean potable water and allow to dry prior to Plaster Gypsum Perlite application.
Do not mix with any additives or products, unless recommended by Saveto. Make sure the substrate is suitable for plaster application. In case of doubt, try on sample area to assess its suitability. Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill zeffects from direct sun and also excessive air-draught during initial curing stage.
Plaster Gypsum Perlite is alkaline, avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
For further information, please refer to material safety data sheet.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
High quality light weight premixed acoustic plaster
High quality light weight gypsum plaster
Sprayable premixed plaster
Sprayable premixed plaster
Fiber reinforced sprayable premixed plaster
Multipurpose low viscosity bonding agent & admixture