Modified cementitious tile adhesive and grout for gypsum substrate.
(Formerly Known as Tilefix GB15)
Vetoset CA548 is a polymer modified cement based adhesive mortar composed of waterproof polymer, hydraulic binders, synthetic resins, selected aggregates, and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which required only addition of clean water to produce easily creamy paste with thixotropic effect. Vetoset CA548 specially formulated to fix ceramic tiles on all types of gypsum substrate. Vetoset CA548 is generally applied at a nominal thickness of 3 mm.
Excellent adhesion to all gypsum based substrates used in building.
Highly thixotropic, no vertical slip.
Extended open time, adjustability time, making installation easier.
Single component easy to mix & apply.
No special primer is required.
Suitable for internal applications.
EN 12002, as S1 if mixed with Vetobond AB432 diluted 1:1
EN 12004, as C1T
Vetoset CA548 supplied in 25 Kg Bag, Coverage: 6-8 m2 @ 3mm thickness
Original sealed container of Vetoset CA548 has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
For the preparation of mortar adhesive, pour into a container 5.0-5.25 liters of water for each 25 Kg bag of Vetoset CA548. Add the powder to the water and mix with a low speed (200-300 rpm) electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 5 minutes and briefly remix with no extra water added.
Spread mixed Vetoset CA548 n the substrate to a uniform thickness of 3 mm using a toothed spatula or trowel, the first pass use smooth side and the second pass use toothed side. Place the tiles onto the fresh adhesive mortar with a firm pressure & slight twisting to ensure a good contact of the adhesive.
Apply enough material that can be tiled within its open time. Spreading large area may result in surface drying the wet adhesive bed before tiles can be fixed, will cause in poor adhesion.
In case of large size tile, it is necessary to spread the adhesive also onto the backside of tiles and then place into fresh adhesive bed.
Remove excess adhesive with a damp cloth before it dries. Joints grouting between tiles may be commenced after 10 hours for walls and 24 hours for floors using Vetoset CA548 or other compatible grouting materials.
Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.
The surface should be sound, clean free from loose material, grease, laitance, dirt etc.
Gypsum substrates should have been allowed to cure sufficiently and should not have humidity more than 10%. All cracks and joints should be treated with Saveto crack filler and Saveto joint fillers.
Vetoset CA548 is cement based and therefore it is highly alkaline. Avoid direct contact with eyes & skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Vetoset CA548 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather resistant cementitious adhesive for ceramic tiles.
Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.
Water resistant grout for swimming pool tile joints.
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
Versatile resin adhesive, cement modifier, bonding agent & sealer