Weather resistant stainless non-sanded smooth tile jointing grout.
Stainless Grout is a cementitious mortar adhesive composed of hydraulic binders, selected aggregates, polymer modified and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable mortar. Stainless grout eliminates the need for sealer. Stainless Grout is applied in thickness from: 2-4 mm for wall tiles and 3-8 mm for floors tiles.
Hydrophobicity properties for stain resistance, uniform colour & durability.
Factory controlled pre-blend ensures consistent high quality.
Requires only addition of water on-site at the time of usage.
Easy tile installation that enables high Productivity.
Excellent bonding on variety of ceramic tiles available in the local market.
Suitable for internal & external applications.
Suitable for horizontal & vertical surfaces.
ASTM C348 & C349
BS: EN 13888
Stainless supplied in Grout 20 Kg Bag
Original sealed container of Stainless Grout has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.
For the preparation of Stainless Grout mortar, pour into a container 6 -7 Liters of water for 20 Kg bag of Stainless Grout . Add the powder to the water and mix with a low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water should be added.
It can also be blended manually for small quantity but ensure correct amount of powder to water is maintained.
If required, add 0.5Ltr of Saveto Bond 2 to the mixing water followed by addition of Stainless Grout powder.
Mixed material can be used within 1 hour. Do not add water to the mix, once the mortar adhesive starts to harden.
Spread the mixed mortar over the tile joints and firmly pressed with rubbing pad covered with sponge rubber spatula.
Stainless Grout mortar is spread diagonally across the joints ensuring that the Stainless Grout is pressed firmly into the joints.
Excess grout that remains on tiles shall be removed with same tool.
After initial setting of 20-30 minutes, depending upon the ambient temperature & humidity, clean the tiles and remove all excess material with a wet sponge.
After full drying, clean the tile surfaces with dry cloth or dispensable cotton towels.
When washing & drying the tiles, ensure tile joints are not rubbed too deep.
Stainless Grout must be kept moist for first 2 days after application to ensure good hardened properties are achieved.
Tools and equipment can be cleaned with water immediately after use. Hardened materials will require removal by mechanical means.
All excess adhesive tiles that are at the level higher than half of the tile thickness shall be removed.
All the joints should be free from dust, loose materials & traces of foreign materials etc. Neutralize the water absorption of the tiles by applying clean potable water.
Do not leave water pooling in the joints.
Stainless Grout is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be washed with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Stainless Grout is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Weather resistant cementitious adhesive for ceramic tiles.
Polymer modified water resistant adhesive for fixing swimming pools, fountains & watertanks tiles.
Water resistant grout for swimming pool tile joints.
Polymer modified weather resistant adhesive for porcelain tiles.
High quality ceramic tile adhesive for projects.
Polymer modified two component cementitious deformable tile adhesive (C2TE S2)