Single component penetrating waterproofing system for concrete
VETOPROOF CM741 provides total and permanent waterproofing solution to water leakage, ingress or seepage in concrete structures or any cementitious substrates due its unique, surface applied penetrative capillary water proofing system. VETOPROOF CM741 works through internal crystallization that seals the pores and hairline cracks in the concretes thus blocking effectively further passage of water. The active chemical that made up VETOPROOF CM741 serves as a catalyst to reactivate crystallization process every time water penetrates into the structure through newly formed capillaries therefore ensuring permanent water tightness.
Vetoproof CM741 supplied in 25 Kg Bags
Yield: 1.6 kg /m² / 1 mm thickness
Original sealed bag of Vetoproof CM741 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.
In the event that the use of masonry brush is the method for application, mix 7 - 7.5 liters of water with 25 kg of Vetoproof CM741, while when a power spray gun is being used, prepare a mixture of 8 – 8.5 liters of water with 25 kg of the product. Mix only as much product as necessary and ensure to stir the mixture regularly. In the event that the mixture starts to set, it is not advisable to add more water, instead simply re-stir the prepared mixture in order to reinstate its workability. Apply Vetoproof CM741 into two coats with the use of a masonry brush or power spray gun. Make sure to apply the second coat while the first coat is still “green”. All areas where Vetoproof CM741 is applied should be kept damp, protected against direct exposure from sunlight, wind and frost by covering the area with polythene sheeting, damp hessian cloth etc. for a period of 5-7 days. Ensure that the period between the application of the first and second layer is between 3 – 4 hours at a temperature of 20°C.
All tools employed for the application of Vetoproof CM741 can be cleaned with water before it hardens otherwise mechanical means are needed.
All surfaces where Vetoproof CM741 has to be applied must be clean and have an open capillary system. Eliminate laitance, dirt, grease and other loose materials by means of high pressure water jetting or wet sand blasting. Defective concretes such as cracks and honeycombs, etc. has to be chased out and repaired prior to the application. In addition, make sure that all surfaces must be damp but not totally wet before progressing the work.
Do not apply Vetoproof CM741 on temperatures below 5°C.
Vetoproof CM741 could not be used as anadditive to concrete or plasters.
Vetoproof CM741 contains cement powders which, when mixed or become damp, release alkalies which can be harmful to the skin. During use, avoid inhalation of dust and contact with skin and eyes. Wear suitable protective clothing, gloves, eye protection and respiratory protective equipment. The use of barrier creams provide additional skin protection. In case of contact with skin, rinse with plenty of clean water, then cleanse with soap and water. In case of contact with eye, rinse immediately with plenty of clean water and seek medical advice. If swallowed, seek medical attention immediately – do not induce vomiting.
Vetoproof CR747 is non-flammable.
Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.
Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.
Single component acrylic waterproofing membrane
Single component elastomeric crack-bridging cementitious waterproof membrane
Single component ultra flexible acrylic waterproofing membrane
Polymer modified water resistant cementitious top coat
High performance crack-accommodating elastomeric acrylic protective and decorative coating for concrete and masonry