Wall & Facade Systems
Cool Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Thermal insulation of residential and industrial concrete buildings.
Save energy consumption related to heating and cooling.
Internally or externally in wet & dry conditions onto block walls & rough surfaces.
Fast Download
Technical Data Sheet
download (*.pdf 0.43Mb)
Technical Information
Product Description

Cool Plaster is blend of OPC, silica sand and graded light weight aggregates plus functional additives for enhancing workability and adhesion. It can be applied on all surfaces after the proper preparation of the surface (primed or using Spatter Dash SB). The product provides thermal insulation for building wall sections relying on advanced material technologies.

  • Excellent thermal insulation properties.
  • Fast mixing application using spray machine
  • Contains special additive that reduces friction and prolongs lifespan of equipment.
  • Factory controlled pre-blend ensures consistent high quality.
  • Requires only addition of water on-site at the time of usage.
  • Uniform color/mass.
  • Improved workability & curing.
  • Easy application with uniform work flow enables high productivity & superior finishing.
  • Strong adhesion on variety of substrates.
  • Internal & external applications.
  • Shrinkages control reduces surface cracks.
  • Suitable for humid & dry conditions.
Compiliance Standard
  • BS:EN 998-1 CSIII, T2
  • Cement type: ASTM C150, type1.
  • ASTM C518
Packaging & Coverage

Cool Plaster is supplied in 15 Kg Bag or Bulk.

Yield: ≈ 24 lit wet/15 kg dry bag

Shelf Life & Storage

Original sealed container of Cool Plaster has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Application Information
Instructions for use

For manual application add to the mixing container 6.3 - 7.2 litres of water for each 15 Kg bag of Cool Plaster or 42 - 48% of weight for machine application. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved.
Manual mixing is allowed for small batch quantities, mix for approx. 1-2 min or when homogeneous mix is achieved.

Smooth Concrete Surfaces
Apply Spatter Dash SB prior to Cool Plaster application, or add 0.5 litres of Vetonit PB434 to the mixing water and adjust the water requirement accordingly for each 20 kg bag. Follow same mixing procedure as described above.
Mixed material must be used within 90 minutes. Do not add water, once the mixed mortar start to harden.

Cool Plaster can be applied in a single or two coats on rough or smooth surfaces by manual or machine application to achieved desired thickness 25-100 mm.
Apply mixed material using spray machine or hawk & trowel technique. Rod or screed to uniform thickness, not exceeding 25 mm for single coat or 25 mm each coat for multiple layers. First layer should be pressed hard against the surface.
For second layer allow the first layer to partially set (60-120min depending on weather). Apply second layer as described above.
Water spray the surface if second layer is carried out next day.

Cool Plaster is best cured by spraying water evenly on the surfaces of applied materials every 12 hrs for minimum of 3 days. During hot & dry conditions allow curing for minimum of 5 days. It will help to obtain high mechanical strengths.

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Cool Plaster, wet the entire surfaces with clean potable water and surface should look damp at the time of Cool Plaster application.

  • Do not mix with any additives or products, unless recommended by Saveto.
  • Make sure the substrate is suitable for plaster application. In case of doubt, try on sample area to assess its suitability.
  • Do not apply the product at temperature less than +5ºC. During summer season the working area must be covered to prevent ill-effects from direct sun and also excessive air-draught during initial curing stage.
  • Tools should be cleaned with water before the mortar hardens. After the hardening its residuals can be removed mechanically only.
Additional Information
Health & Sefety

Cool Plaster is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of cold water. Seek medical advise.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Masonry Grout Filler

Premixed cementitious masonry grout


Premixed cementitious masonry mortar

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

view more
Featured Product
Vetorel XT420

Water based mold and form-work release agent

Vetorel XT420 is used for the treatment of wooden and metal form work or molds prior to the casting of concrete to facilitate form stripping
Minimizing concrete surface blemishes and pinholes
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map