Flooring & Coatings Systems
Vetotop CX534

Premixed 20 to 100 mm thick conventional cementitious mortar.

Uses
Cost effective cavity filling in non-structural areas.
Non-structural backing mortar.
Filling around underfloor heating installations and mechanical fittings.
Fast Download
Technical Data Sheet
download (*.pdf 0.20Mb)
Method of Statement
download (*.pdf 0.20Mb)
Catalogues
Flooring Technical Brochure
download (*.pdf 9.29Mb)
Technical Information
Product Description

Vetotop CX534 is a single component cementitious backing mortar composed of hydraulic binders, silica sand and selected aggregates. It is supplied in bulk as a dry pumpable powder ready to use on site, once mixed it will form a trowellable mortar that is applied in thicknesses between 20 and 100 mm.

Advantages
  • Factory controlled pre-blend ensures consistent high quality.
  • Suitable for Middle East harsh weather conditions.
  • Easy application enabling high productivity through pumps and horizontal mixers.
  • Easy to break and refurbish backing to install additional piping and mechanical fittings.
  • Excellent workability.
  • Replaces conventional site batched mortars.
  • Applied on horizontal damp compacted sand and cementitious substrates while providing good adhesion.
  • Contains special additive that reduces friction and prolongs lifespan of equipment.
Compiliance Standard

- ASTM C 150
- ASTM C 207
- ASTM C 136

Packaging & Coverage

Vetotop CX534 is supplied in 30 Ton Silo, Yield: 0.5 - 0.6 Ltr / Kg

Shelf Life & Storage

Vetotop CX534 has a shelf life of 12 months provided it is stored clear of ground in a dry and shaded place below 35ºC.

Colors
Grey colour powder
Application Information
Instructions for use

Application


Vetotop CX534 can be applied in a single layer to the desired thickness using HM 24 machine. Rod or screed to a uniform thickness immediately then follow with installation of the tiles. To insure better coverage increase the thickness and firmly press on the tile squeezing the excess out. For better adhesion you can use Vetobond PB434 product call technical engineer for advice.

Curing


Vetotop CS534 is best cured by spraying water on the surfaces of the tiles before grouting for 2-3 days. During hot & dry conditions allow curing for minimum of 5 days.

Cleaning


Clean tools with water promptly before material hardens. Hardened material can be mechanically removed.

Surface Preparation

Surface Preparation

Substrate should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc. Prior to Vetotop CX534 Application, wet the entire surfaces with clean potable water and surface should look damp at the time of application.

Mixing

For application using HM 24 Mixing & pumping machine, the water flow rate is 300-500 Lit/hour. Mixed material should be used within 1 hour.
Re-tempering is allowed between 60 and 90 minutes for one time only.

Limitation

Design Criteria

Vetotop CX534 is designed for application for pumpingmachine (HM 24) and contains special shrinkage control additive and provides good adhesion. The product is available in Grey color only  and can be applied in thickness from 2 to 10 cm.

Additional Information
Health & Sefety

Vetotop CX534 is highly alkaline therefore avoid direct contact with eyes or skin. Vetobond BR434 is latex emulsion. It is recommended to use protective gloves and goggles during application.
Any skin contact should be washed with plenty amount of water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advice.
Vetotop CX534 is non-flammable.

More Products from this section
Vetotop XT539

Non-metallic emery based dryshake monolithic floor hardener

Vetotop CL530

Premixed 2 to 10 mm thick cementitious self leveling underlayment

Vetotop CS535

Premixed 10 to 30 mm thick cementitious screed.

Vetotop CS536

Premixed 30 to 100 mm thick cementitious screed.

Vetotop EC198

Chemical & abrasion resistant anti bacterial wall & floor thin epoxy coating

view more
Featured Product
Vetonit Base WR

Weather Resistant Premix Cement Coating for Internal Use

Uses
Can be applied internally onto walls & ceiling surfaces.
On concrete surfaces that are smooth and also on precast concrete surfaces.
On wall surfaces that are plastered with water resistant plasters, Vetonit Renders and on damp concrete interiors.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map