Wall & Facade Systems
Masonry Grout Filler

Premixed cementitious masonry grout

Uses
Masonry Grout Filler can be applied on cement based masonry blocks, masonry units, behind marble and cement panels, tiles or slabs, etc.
Masonry Grout Filler is also suitable for application behind gypsum boards
Fast Download
Technical Data Sheet
download (*.pdf 0.20Mb)
Method of Statement
download (*.pdf 0.19Mb)
Catalogues
Decorative Coating Brochure
download (*.pdf 2.78Mb)
Plastering Systems Technical Guide
download (*.pdf 9.93Mb)
reference projects
Project:
King Khalid University
Location:
Saudi Arabia
Description:
Housing & Parking projects
Contractor:
Al Jabreen Contracting
Consultant:
Parking: Zuhair Fayez Housing: Saud Consult
Technical Information
Product Description

Masonry Grout Filler is a fine grout category as defined by American Concrete Institute (ACI), and composed of portland cement, natural sand, selected fine aggregates and special additives. The Masonry Grout Filler contains admixtures in accordance to ASTM C 476, C207, C260 to meet fine grout category. Masonry Grout Filler is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce pourable grout.  Masonry Grout Filler is ideal for grouting masonry blocks, masonry units, cores and also as a filler behind marble slabs etc.. Masonry Grout Filler can be applied in  a grouting gaps from 10 mm to 100 mm.

Advantages
  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Suitable for ME harsh weather conditions
  • Easy application with uniform work flow enables high productivity & superior finishing
  • Strong adhesion
  • Good mechanical resistance
  • Excellent workability
Compiliance Standard
  • ASTM C 476, C207
  • ASTM C 404, C260
  • ASTM C 150 Type 1
Packaging & Coverage

Masonry Grout Filler is supplied in 50 Kg Bag
Coverage - 1.5 - 1.8 Kg/m2 / mm Thickness

Shelf Life & Storage

Original sealed bags of Masonry Grout Filler has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Application Information
Instructions for use

Mixing

For the preparation of masonry grout mixture, pour into a container 7.75-8.25 litres of water for each 50 Kg bag of Masonry Grout Filler.

Slowly add the powder to the water while mixing with electric drill fitted with a suitable paddle for 2 minutes. Then continue mixing at medium-high speed for another 2-3 minutes, until a uniform, lump free pourable consistency mix is achieved. Total mixing time is 4-5 minutes approx. Do not add water to the mix once it starts to stiffen.

Application

Pour the mixed material into the gap between masonry blocks, cement panels or behind marble or gypsum board within the open time of 30-45 min.

Avoid air entrapment between the gaps while pouring the grout material.

For high lift grouting, the mixed material should be pumped or poured from a height to ensures the desired grout flow so that it spreads smoothly within the gaps.

We recommend use of mechanical grout pump for placement of masonry grout as it will give more efficient filling and also help in grout pumping in high rise structures.

Cleaning

All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

The surface should be sound, clean free from loose materials, grease, laitance, dust etc.

Additional Information
Health & Sefety

Masonry Grout Filler is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application. Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.

Masonry Grout Filler is non-flammable. For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification.

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Cool Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

Vetonit MASONRY MORTAR

Premixed cementitious masonry mortar

Vetotherm FLEX

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm ULTRA

Cementitious based adhesive and base coat for EIFS / ETICS

Vetotherm Plaster

Advanced Modified Cementitious Thermal Insulating Plaster

view more
Featured Product
Vetorep ER355

High strength, abrasion resistant epoxy based repair mortar

Uses
Repair of concrete elements in industrial applications where chemical resistance is needed
Reinstatement of structural elements where minimum shutdown time is required
Acid tanks lining, sea walls repair, industrial floors repair
Horizontal and vertical repairs
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map