Qatar
Bahrain Egypt Jordan Saudi Arabia UAE
EN
EN
Contact news and events About us Home
PRODUCT RANGE
SYSTEM
Selector REFERENCES DOWNLOAD SECTION
Renders & Finishes
Vetonit FINISH WR

Water resistant internal use premix smooth cement coating

Uses
Leveling of minor surface undulation of plaster and concrete.
Applied internally onto walls & ceiling surfaces and suitable for use in wet areas like bathrooms, toilets & kitchens.
On concrete surfaces that are smooth and also precast concrete surfaces.
As a thin patch mortar, pin hole filler and color matching coat.
Fast Download
Technical Data Sheet
download (*.pdf 0.22Mb)
Method of Statement
download (*.pdf 0.21Mb)
MSDS
download (*.pdf 0.86Mb)
reference projects
Project:
Baha University, Administration Building
Location:
Saudi Arabia
Description:
Administration Building
Contractor:
Al Joudah
Consultant:
Otaishan Consulting
Technical Information
Product Description

Vetonit Finish WR is a cement based smooth finishing coat composed of hydraulic binders, selected aggregates and special additives. It is supplied as a dry powder in pre-weighed bags ready to use on site, which requires only addition of clean water to produce easily workable material. Vetonit Finish WR is a high quality product for multipurpose use. Vetonit Finish WR can be applied in thickness from 1 mm to 5 mm, in one or two layers depending on site requirement.

Advantages
  • Factory controlled pre-blend ensures consistent high quality
  • Requires only addition of water on-site at the time of usage
  • Manual or spray machine application
  • Superior workability
  • Easy application that enables high productivity
  • Excellent Adhesion on variety of substrates
  • Water resistant.
  • Suitable for humid & dry conditions
  • Suitable for vertical & ceiling surfaces
Compiliance Standard
  • BS:EN 1015 - 12 (per BS EN 998)
  • ASTM C348
  • ASTM C109
  • BS:EN 413-2
Packaging & Coverage

Finish WR supplied in 25 Kg Bag
Consumption: 1.0 - 1.2 Kg/m²

Shelf Life & Storage

Original sealed bags of Finish WR has a shelf life of 12 months provided it is stored clear of ground in a dry shaded place below 25ºC.

Colors
White & Grey Powder
Application Information
Instructions for use

Mixing

Internal Block Walls & Rough Surfaces

For manual application add to the mixing container 9.5-12.0 litres of water for each 25 Kg bag of Vetonit Finish WR. For Spray machine application use 12.0-14.0 litres of water for each 25 kg bag. Add the powder to the water and mix with a mechanical plaster mixer or low speed electric drill fitted with a suitable paddle for 3-4 minutes, until a uniform, lump-free consistency is achieved. Allow the mixed material to stand for about 10 minutes and remix briefly with no further water to be added.

Smooth Concrete Surfaces & Ceilings

Add 0.5 litres of Vetonit Bond 2 to the mixing water and adjust the water requirement accordingly for each 25 kg bag. Follow same mixing procedure as described above.
Mixed material can be used within 3 hours. Do not add water to the mix once the mixed mortar start to harden.

Application

Vetonit Finish WR can be applied in one or two layers as required to achieve desired thickness of 1-3 mm.
Various grades of finish textures can be obtained by selecting appropriate spray machine nozzle sizes.
Allow the installed application to remain undisturbed for at least 48 hours.

Curing

Vetonit Finish WR is best cured by spraying water on the surface of applied material every 12 hrs for minimum 3 days. In case of using  Vetonit Finish WR as underlayment layer to receive a final  finishing system, you can add 1 liter of Vetonit Bond 2 / Bag to improve curing process. This will help in achieving uniform colour, minimize risk of surface cracks and high mechanical strengths.


Cleaning

All tools should be cleaned immediately after finishing by water. Hardened materials can be cleaned mechanically.

Surface Preparation

The surface should be sound, clean, free from loose material, grease, laitance, dirt curing compound, etc.
Prior to Finish WR application, wet the entire surfaces with clean potable water and surface should look damp at the time of Finish WR application.

Additional Information
Health & Sefety

Finish WR is highly alkaline therefore avoid direct contact with eyes or skin. It is recommended to use protective gloves and goggles during application.
Any skin contact should be wash with soap & water. In case of eyes irritation, immediately wash with copious amount of clean cold water. Seek medical advise.
Vetonit Finish WR is non-flammable.
For further information, please refer to material safety data sheet.

Important note

Saveto endeavors to ensure that any advice, recommendations, information it may give, is accurate and correct. It cannot accept any liability either directly or indirectly arising from the use of its products, because it has no direct or continuous control over where or how its products are applied, whether or not in accordance with any advice, specification, recommendation or information given by us. Saveto has the right to change any of the specifications mentioned in the Technical data sheets upon its discretion without prior notification. 

Hard copies of TDSs are printed once or twice a year, while our technical data sheets are continuously being updated as per R&D improvements and new 3rd party testing; kindly refer to our website for the latest updated TDSs.

More Products from this section
Vetonit Crack Filler

High quality premixed surface crack filler

Vetonit FINISH WR EG

Water resistant external use premix smooth cement coating

Vetonit Gypsum Joint Compound

Premium quality premixed compound for gypsum board joints

Vetonit Putty WR

Water resistant high quality premixed putty

Vetonit Base WR EG

Weather Resistant Premix Cement Coating for External Use

view more
Featured Product
PREMIUM PROJECT FIX

High quality ceramic tile adhesive for projects.

 

Uses
For ceramic tiles.
Tiling on smooth concrete surfaces, lightweight bricks, blocks, plaster boards.
Tiling on wall surfaces that are plastered with water resistant plasters such as Vetonit Render & Vetonit Base WR on damp concrete interiors.
Suitable for dry & wet conditions.
Contact us
Choose a country
Saudi Vetonit Co. Ltd. (SAVETO)
P.O. Box 52235 Riyadh 11563, KSA
Toll: (+966 11) 265 3334
Fax: (+966 11) 265 0936
Sales
800 124 9009
Fax: (+966 11) 265 0718
Email: sales@saveto.com
Site Map
Home
About us
news and events
Contact
DOWNLOAD SECTION
REFERENCES
Copyright ©2015-2016 Saudi Vetonit Co. Ltd. All Rights Reserved.